50% OFF Launch Offer: $24.99 (Reg. $49.99) · Free Tracked Shipping · Ships in 24h
Claim Offer ❯
Excellent4.8 (247)Trustpilot

Kill the hum. Keep the music.

Cosari StudioLink X14

A shielded oxygen-free copper interconnect with brushed silver metal plugs and ribbed strain-relief boots.

Claim 50% Off — Order Now

In Stock – Free 5–7 Day US Shipping

  • 1/4-inch TS to 3-pin Male XLR
  • 95% OFC spiral hum shield
  • Machined metal shells with gold tip
  • 2-year zero-crackle warranty
Cosari StudioLink X14
Free Tracked Shippingin 5 to 7 business days
30-Day Home Trialtry it risk-free at home
Pay with PayPalVisa, Mastercard or Klarna
24-Hour Supportfast, helpful customer care

Built for Silence, Made to Last

Every part of the StudioLink X14 targets the two things that ruin sessions and gigs: hum and crackle.

Shielded OFC Core

A 99.99% oxygen-free copper 22AWG conductor sits inside a 95% copper spiral shield that blocks buzz from chargers, routers and power strips.

Two Precision Ends

A 3-pin male XLR latches cleanly into speakers and mixers. A 24K gold-tipped 1/4-inch TS plug seats with a firm click in interface and controller outputs.

Ribbed Strain Relief

Segmented rubber boots spread every bend over an inch of cable, so tight rear-panel corners don't stress the solder joints.

Measured Quiet

In our power-brick test it held a -98dBFS noise floor with no visible 60Hz spike, even draped across a live laptop charger.

How the StudioLink X14 Keeps Your Signal Clean

Clean Contact at Both Ends

Clean Contact at Both Ends

Solid silver-plated XLR pins and a 24K gold-plated TS tip resist oxidation, so the connection stays tight and quiet year after year.

Bends Without Breaking

Bends Without Breaking

The ribbed rubber boot curves smoothly behind a monitor sitting close to the wall, taking load off the joint instead of folding the cable at the shell.

Quiet Next to Power

Quiet Next to Power

Route it past your power strip and chargers. The dense copper shield keeps interference out of the signal headed to your speakers.

Cosari StudioLink X14 hero
Excellent4.8 (247)Trustpilot

Limited-Time Direct Offer — Save 50% Today

Cosari StudioLink X14

1/4-Inch TS to 3-Pin Male XLR Studio Interconnect with Machined Metal Shells and 24K Gold Tip

Backed by our 30-Day Money-Back Trial & Full Cosari Guarantee.

$24.99 $49.99 Free Tracked Shipping (5–7 Days) Included

In Stock: Delivers in 5–7 Business Days. Free insured US delivery with tracking.

30-Day Money-Back Guarantee plus a full 2-Year Warranty.

Quantity

1
Add to Cart
PayPalVisaVISAMastercardKlarnaKlarna.
Secure Checkout5–7 Day Tracked Delivery30-Day Trial
Description

Connectors and wiring: 3-pin male XLR to 6.35mm (1/4-inch) unbalanced TS mono plug. Pin 2 to Tip, Pins 1 and 3 to Sleeve. Compatible with powered studio monitors, PA speakers and mixer XLR inputs.

Cable construction: 99.99% oxygen-free copper 22AWG signal core, 95% copper spiral shield and a 6.0mm matte-black PVC jacket that lays flat with no coil memory.

What it is not: This is not a female-to-male microphone cable and it is not meant for 100-foot snake runs. It is built for short desk and stage connections from 1/4-inch outputs to XLR inputs.

5–7 Day Shipping & 30-Day Returns

Free 5–7 Day US Shipping: Every order ships free with full tracking and delivers in 5 to 7 business days.

30-Day Trial: Try it at home for 30 days risk-free. Need help? Email us anytime at support@buycosari.com.

2-Year Warranty: If anything goes wrong within 2 years, we replace it free of charge or refund your order in full.

Why Choose the Cosari StudioLink X14?

Cosari StudioLink X14 Detail

Machined Metal Grip

Ribbed collars on brushed silver shells give your fingers something to hold, even under dim booth lighting or behind a crowded rack.

24K Gold Contact

The gold-plated TS tip won't tarnish, so the connection stays as quiet in year two as it was on day one.

2-Year Zero-Crackle Promise

If either plug ever crackles within two years, Cosari sends a new cable free. Plus 30 days to return it for any reason.

Cosari StudioLink X14 vs. Ordinary Alternatives

Cosari StudioLink X14Standard Competitors

FeatureCosari StudioLink X14Standard Competitors
Noise next to a power strip-98dBFS, no visible 60Hz spikeAudible hum, around -74dBFS
Connector shellsBrushed silver metal with ribbed grip collarsMolded plastic
Strain reliefSegmented ribbed rubber bootsThin, stiff plastic neck
Conductor99.99% OFC 22AWGOften copper-clad aluminum
Warranty2-year zero-crackle replacementUsually 30 to 90 days
Order Now & Save 50%

What's Included

In the Box
  • 1 × Cosari StudioLink X14 cable (1/4-inch TS to 3-pin Male XLR)
  • 1 × Hook-and-loop cable tie strap
  • 1 × Pinout quick-start card
Technical Specifications
  • Connector A: 3-pin Male XLR, zinc-aluminum alloy shell, brushed silver finish
  • Connector B: 6.35mm (1/4-inch) TS mono plug, 24K gold-plated tip
  • Wiring: XLR Pin 2 to Tip, Pins 1 and 3 to Sleeve (unbalanced)
  • Conductor: 99.99% oxygen-free copper, 22AWG
  • Shielding: 95% density copper spiral
  • Jacket: 6.0mm matte-black PVC
  • Strain relief: Ribbed rubber boots, rated 15,000+ bend cycles
  • Lengths: 6 ft (1.8 m) or 10 ft (3 m)
Care & Safety
  • Always grip the ribbed collar, not the cable, when unplugging. Press the XLR latch on your speaker or mixer before pulling the XLR end out.
  • Coil the cable loosely using the over-under method and secure it with the included strap. Avoid sharp folds right at the boots and keep the gold tip clean and dry.
  • Backed by our 30-Day Money-Back Guarantee & Full Cosari Warranty
  • Customer Support: support@buycosari.com
In the Box Cosari StudioLink X14

Set Up in Under a Minute

Swipe left for steps 2 and 3

  1. Uncoil
    1

    Uncoil

    Release the strap and lay the cable flat. It uncoils without kinks or spring-back.

  2. Plug in the 1/4-inch end
    2

    Plug in the 1/4-inch end

    Grip the ribbed collar and push the gold-tipped TS plug into the line output of your interface, controller or synth until it clicks.

  3. Connect the XLR end
    3

    Connect the XLR end

    Click the male XLR into your powered monitor or mixer input, switch on, and enjoy a quiet noise floor.

Verified Customer Reviews

What 200+ Verified Buyers Say About the Cosari StudioLink X14

Excellent Trustpilot
4.8
Based on 247 verified reviews
5 Stars
212
4 Stars
25
3 Stars
7
2 Stars
2
1 Star
1
97% of buyers recommend the Cosari StudioLink X14
Filter by topic
Customer photo
✓ Verified Purchase
Marcus V.3 days ago

Completely killed the 60Hz hum on my Yamaha HS8s

I finally upgraded my studio monitors and interface last month, only to spend two hours chasing a nasty buzz coming from a $9 Amazon cable running past my power strip. Swapped in a pair of these Cosari StudioLink X14 cables and the noise floor dropped to dead silence. The brushed silver metal shells have real weight to them, and the segmented rubber boots bend cleanly behind my studio desk right up against the drywall.

Verified Purchase · Austin, TX · Cosari StudioLink X14

Customer photo
✓ Verified Purchase
Devon K.5 days ago

Gold 1/4-inch tip clicks in like a rifle bolt

Stopped buying cheap molded Hosa cords forever. The gold 1/4-inch TS tip on the StudioLink X14 clicks into my synth and audio interface outputs with zero play and zero static when the keyboard stand shakes. Even coiled up next to my mixer on the studio desk, the black PVC jacket lays completely flat with no stiff plastic kinks. Spend ten bucks more once for real machined metal housings and forget your cables exist.

Verified Purchase · Nashville, TN · Cosari StudioLink X14

✓ Verified Purchase
Trey M.1 week ago

Saved my mobile DJ setup from intermittent cutouts

Nothing makes you look more amateur at a paid wedding gig than wiggling a cheap 1/4-to-XLR cord while the left QSC top cuts in and out. My old cables started crackling after four gigs whenever the 1/4-inch end got nudged on my DJ controller. These Cosari plugs have serious strain relief and the ribbed grip collar on the silver barrels makes pulling them out of a dark stage snake at 1 AM ten times easier.

Verified Purchase · Chicago, IL · Cosari StudioLink X14

✓ Verified Purchase
Julian R.1 week ago

Feels like a $70 Mogami without the painful price tag

It is always painful spending $130+ with tax just for two short patch cords between an interface and powered monitors. At 50% off, I grabbed four of these for my home rack. The XLR barrel tolerances are spot-on—slides smoothly into my Mackie mixer channels without getting stuck like other thick metal plugs I've tried, and the signal is dead quiet.

Verified Purchase · Los Angeles, CA · Cosari StudioLink X14

✓ Verified Purchase
Chris P.2 weeks ago

No more gunshot pops when nudging my speakers

With my previous budget cable, I moved my monitor two inches on my desk and heard a gunshot POP—unscrewed the plastic shell and the ground wire was hanging by two pathetic strands. You can immediately feel the difference with the Cosari StudioLink X14. The brushed metal barrels, black accent rings, and thick rubber boots lock the cable down so nothing twists inside the solder joints.

Verified Purchase · Seattle, WA · Cosari StudioLink X14

✓ Verified Purchase
Aaron L.2 weeks ago

Rock solid studio interconnect, wish they made a 25-foot version

Build quality on the connectors is a straight 10/10. The 24K gold TS plug and 3-pin male XLR fit snug in my Focusrite and JBL 305Ps with zero hum even crossing over two monitor power bricks. Only knocking half a star because I'd love a longer 25ft run for the far corner of my live room, though for desk and rack work this length is ideal.

Verified Purchase · Denver, CO · Cosari StudioLink X14

✓ Verified Purchase
Samir H.3 weeks ago

Zero memory coils straight out of a cold gig bag

Half the battle with stage and studio patch cords is fighting stiff jackets that act like frozen rebar. This black PVC jacket has a smooth, supple feel that uncoils flat on the first throw and wraps right back up using over-under without fighting you. Easily the cleanest 1/4-inch TS to male XLR adapter cable in my road case.

Verified Purchase · Atlanta, GA · Cosari StudioLink X14

✓ Verified Purchase
Nate W.3 weeks ago

Cleanest run from my pedalboard amp modeler to FOH snake

I run a stereo 1/4-inch output from my modeler straight into the stage XLR snake every Sunday morning. Cheap adapters always gets kicked and bent. Having a dedicated one-piece cable with heavy brushed silver shells and proper ribbed rubber strain boots gives me total peace of mind on stage.

Verified Purchase · Dallas, TX · Cosari StudioLink X14

✓ Verified Purchase
Elena G.1 month ago

Tip never loosens inside my synth jacks

I've had budget metal plugs where the 1/4-inch tip literally unscrewed itself inside my vintage synth output jack mid-session. The machined tolerances on the Cosari StudioLink X14 are tight and unified. Plugged and unplugged it dozens of times re-patching my outboard compressor and it still feels brand new.

Verified Purchase · Brooklyn, NY · Cosari StudioLink X14

✓ Verified Purchase
Brandon T.1 month ago

Replaced all six patch cords in my bedroom studio

Ordered two to test on my main monitors and immediately came back for four more while the 50% off deal was still live. If you have powered studio monitors with XLR inputs and an audio interface or mixer with 1/4-inch outputs, stop messing with rattling adapters and get these.

Verified Purchase · Portland, OR · Cosari StudioLink X14

Stop chasing hum. Start making music.

$24.99 $49.99 Free Tracked Shipping (5–7 Days) Included

Claim 50% Off — Order Now

In Stock – Free 5–7 Day US Shipping · 30-Day Risk-Free Trial.

Frequently Asked Questions

Can I use the StudioLink X14 as a microphone cable?

No. It has a 1/4-inch TS plug on one end and a male XLR plug on the other. A vocal mic needs a female XLR to male XLR cable. The X14 is built to connect interfaces, controllers, synths, pedalboards and mixers to XLR inputs on powered speakers and mixers.

Will this cable fix the hum in my monitors?

If the hum comes from a cheap, poorly shielded cable picking up interference from chargers or power strips, yes. In our test it measured -98dBFS draped across live power bricks. If the hum is a ground loop caused by your gear being on different power circuits, try plugging everything into the same strip first. No cable can fix a ground loop on its own.

What is the pinout?

XLR Pin 2 is wired to the 1/4-inch Tip, and Pins 1 and 3 are wired to the Sleeve. This is the standard unbalanced wiring that works with powered studio monitors, PA speakers and mixer inputs.

Does it work with Yamaha HS5, KRK Rokit or JBL 305P monitors?

Yes. All three have female XLR inputs on the back. Plug the XLR end into the monitor and the 1/4-inch end into your interface or controller output. Most stereo setups need two cables, one for left and one for right.

What lengths are available?

The X14 comes in 6 ft (1.8 m) for desktop setups and 10 ft (3 m) for most stage and DJ booth runs. Because the TS side is unbalanced, we recommend choosing the shortest length that reaches.

What if it crackles or I don't like it?

You get a 30-day money-back guarantee, so you can test it on your own rig. If a plug ever crackles within two years, Cosari replaces the cable free under its zero-crackle warranty.

Cosari StudioLink X14In Stock · 30-Day Trial
Order Now & Save 50%