Full-palm torque for 4-inch gaps.
A 54mm rubberized dome, a 38-tooth ratchet that clicks every 9.47°, and a notched S2 shaft that adjusts from 92mm.
Claim 50% Off — Order NowIn Stock – Free 5–7 Day US Shipping
Four engineering decisions that separate the TorqueStub 38T from drawer-filler stubbies.
A heat-treated Cr-V gear engages every 9.47° of wrist swing, with under 2.1 N·cm of back-drag. Short swings drive the screw, and the return stroke leaves it where it is.
Six deep axial channels in oil-resistant TPE give your whole hand something to lock into, so you can lean in like you would on a T-handle instead of pinching a cork.
HRC 58–60 S2 steel with PH2 on one end and SL6 on the other. Three ball-detent notches adjust the tool from 92mm to 135mm overall, with no axial play.
Glossy ribbed collar with firm Left / Lock / Right detents. A neck channel keeps your fingers off it mid-turn, and the lock position is rated to 48 N·m.
Flick the ribbed collar to Right to drive, Left to remove, or center to lock for breaking loose a stuck screw. The detents are firm enough to feel without looking.
Pull the S2 shaft, flip it for Phillips or slotted, and click it into one of three notches. You can go from true stubby to mid-reach in about two seconds.
Press your palm into the dome and swing less than 10° per click. The screw goes in straight, even when a wall stops your hand after two inches.
Limited-Time Direct Offer — Save 50% Today
38-Tooth Stubby Ratcheting Screwdriver with Full-Palm Grip & Adjustable S2 Shaft
Backed by our 30-Day Money-Back Trial & Full Cosari Guarantee.
$34.99 $69.99 Free Tracked Shipping (5–7 Days) Included
In Stock: Delivers in 5–7 Business Days. Free insured US delivery with tracking.
30-Day Money-Back Guarantee plus a full 2-Year Warranty.
Quantity
Description: The Cosari TorqueStub 38T is a stubby ratcheting screwdriver built around a full-size grip. A 54mm matte black and green TPE dome, a 38-tooth low-drag ratchet, and a reversible notched S2 steel shaft let you drive #2 Phillips and 1/4-inch slotted screws inside cavities as tight as 95mm.
Materials & Build: Cross-linked oil- and solvent-resistant TPE over a high-impact nylon core. Heat-treated Cr-V ratchet gear with a factory-lubricated dual-pawl mechanism. S2 alloy steel shaft hardened to HRC 58–60, with a phosphate anti-corrosion finish and magnetized tips.
Shipping & Returns: Free tracked shipping on every order. A 30-day money-back guarantee applies from delivery, and the ratchet pawl and shaft carry a 2-year warranty.
Free 5–7 Day US Shipping: Every order ships free with full tracking and delivers in 5 to 7 business days.
30-Day Trial: Try it at home for 30 days risk-free. Need help? Email us anytime at support@buycosari.com.
2-Year Warranty: If anything goes wrong within 2 years, we replace it free of charge or refund your order in full.
At 92mm overall, it sits square to the screw in under-sink, under-dash, and furnace cavities, so the bit seats properly instead of camming out at an angle.
Both shaft tips are permanently magnetized and hold a screw sideways long enough to start it in a blind hole behind a blower motor.
The locked ratchet is rated to 48 N·m, so when a rusted screw finally gives, the bit or screw head will give before the tool does.
Cosari TorqueStub 38TStandard Competitors
| Feature | Cosari TorqueStub 38T | Standard Competitors |
|---|---|---|
| Ratchet swing per click | 9.47° (38-tooth) | 15° or more (24-tooth typical) |
| Loose screw on return stroke | Stays put (<2.1 N·cm back-drag) | Often spins back out |
| Grip with oily hands | 54mm ribbed TPE dome holds | Hard plastic slips |
| Accidental direction change | Recessed collar, zero bumps in testing | Collar sits in the grip zone |
| Reach adjustment | 92–135mm, three notches | Fixed length |
Swipe left for steps 2 and 3
Slide the S2 shaft in with the tip you need facing out and push until the ball detent clicks into your chosen notch.
Thumb the ribbed collar to Right to drive, Left to remove, or center to lock.
Press into the dome and use short wrist swings. The screw goes home without re-gripping.
Used it to replace a blend-door actuator under my F-150 dashboard where there's literally 4 inches of clearance. Most stubby drivers shrink the handle for a toddler's fingertips, but this wide rubberized palm dome lets you lean your palm right into it while the 72-tooth ratchet clicks with tiny wrist flicks. Saved me hours of misery.
I have four different stubby drivers in my top drawer and every single one either slips under real torque or takes half a turn before the tooth clicks. That fat matte black and green ribbed grip locks right into your hand when your palms are covered in motor oil, and the notched shaft clicking out to three different lengths is super handy on intake clamps.
Zero wobble on the dark steel shaft and the ratchet mechanism has almost no back-drag. The second you try to back-ratchet on a loose screw inside a wall box or breaker panel, the screw stays put instead of spinning back out with the bit. Worth every penny.
Every time I gripped my old stubby tightly to break a corroded screw loose, my index finger would bump the cheap directional ring into neutral and strip my knuckles. The glossy ribbed collar on the Cosari has super positive detents between Left, Locked, and Right—you can flick it with one thumb without looking.
I didn't expect a compact stubby to break loose rusted patio door-hinge screws that my regular 8-inch driver cammed out on, but the downward palm leverage you get on this dome is insane. Locked the collar in center position, leaned into it, and it popped free on the first try.
Paid $65 for a hyped YouTuber screwdriver that feels like a slippery plastic tube; this bulbous rubber grip puts down way more actual torque on stubborn hose clamps and brackets. Plus the reversible PH2 and 6mm slotted shaft locks in rock solid.
Both ends of the shaft hold #2 Phillips and slotted screws tight enough to guide them sideways into a blind hole behind a furnace blower without dropping them. Only giving 4 stars because the notched shaft is proprietary so you only get PH2 and 6mm flathead, though honestly that covers 95% of what I grab a stubby for.
Bought this specifically for a loose dishwasher mounting tab and garbage disposal bracket where a normal screwdriver hits the PVC trap. Telescoped the shaft all the way in and had plenty of knuckle clearance. Ratchet action is buttery smooth.
Having the notched dark-gray steel shaft click out to three different lengths is genius—it goes from a true knuckle-clearance stubby to a mid-length reach driver in two seconds. Lives in the top tray of my roll cart now.
Heavy, solid feel in the palm and the Cr-V tip hasn't shown a single mark after three weeks of daily HVAC service calls. The green rubber ribs wipe clean easily and never feel greasy.
$34.99 $69.99 Free Tracked Shipping (5–7 Days) Included
In Stock – Free 5–7 Day US Shipping · 30-Day Risk-Free Trial.
Yes. The center position on the ribbed collar locks the 38-tooth pawl, which is rated to 48 N·m (425 in-lbs). That is well beyond what a hand can put through a #2 bit, so the lock won't be the weak point.
Push the collar, pull the shaft out, and either flip it end-for-end (PH2 or 1/4-inch slotted) or slide it to one of three machined notches. A ball detent clicks it into place, adjusting exposed shaft length from 22mm to 65mm and overall tool length from 92mm to 135mm.
Yes. Both ends of the S2 shaft are permanently magnetized and will hold a #2 Phillips or slotted screw horizontally for starting in blind holes.
The grip is cross-linked, oil- and solvent-resistant TPE molded directly over a high-impact nylon core, so there is no glued sleeve to peel. Wipe off brake cleaner or oil after use and it will stay tacky without turning gummy.
In our testing, never. A recessed neck channel separates the palm dome from the selector collar, so your grip sits on the rubber and your thumb has to reach on purpose to change direction.
Use it on your toughest under-dash, cabinet, or engine-bay screws for 30 days. If the ratchet skips, the back-drag unwinds a loose screw, or it simply doesn't beat the stubbies already in your drawer, return it for a full refund. The ratchet pawl and S2 shaft are also covered for 2 years.